Hook up two amps to one sub, can you hook up a sub to a 2 channel stereo system

Is this possible or recommended? For example lets say you hook up the rca's from your head unit to an amp that is watts. But the more subs an amp is placed on, the less power it can give to each individual sub. Even though I put the Bluetooth special mode in rear with subwoofer it still takes up both channels for the rear I can't split the other one.

Determine whether you need multiple batteries and capacitors. Also the head unit is an alpine Bluetooth etc head unit I can get the model number off the box if need be. Unfortunately, as it is with most consumer-grade electronics, it will probably make more economic sense to replace the whole system rather than repairing the malfunctioning one. You can certainly mount a capacitor as you describe, but I don't think it would be very effective.

Can I Connect Two Amps To One Sub

Hi Buck, I have a question not related to this audio setup. The rest of your description indicates you're aware of what's involved and have a good plan for a successful install. And do you see any problems with this set up? Can a watt amplifier push two watt subwoofers?

How do you hook two subs up to one amp

The short answer is that you can use any number or combination of power amps in a car audio setup as long as you wire them in properly. What's the best way to wire them to get good bass? Most people run one wire from the receiver to one amp, and then daisy-chain another wire to the second amp. You are in line to receive a call from.

How do you wire 2 amps together

Is that too much for the factory small gauge wiring? What would be the best way to wire the subs to get the maximum Bass. Your reply will be sent to Continue where you left off.

And if so, is this parallel or series. And finally, am I going about this all wrong, should I be looking at an entirely different setup altogether? Make sure each amp has its own separate ground.

Jake, Not only are there no problems doing this, here's an article explaining the technique. If it blows again, you'll have to continue checking your power wiring, amp connections, and speaker wiring for any abnormalities. You should be alright as long as you never play distortion, academics online trying to get louder bass. Cookies make wikiHow better.

Use a connection in the vehicle's fuse box that turns on and off with the car, if your receiver has no remote connection. Or any other subwoofer's, preferably inches that would be good for this amp. Wire can burn and melt if too much current is running through it so one wire is your best bet. Mike, Despite that amplifier's published specifications, I think that it only has enough power for one of those subs but not two. Josh, You still have not identified your gear by model numbers.

Can you hook up a sub to a 2 channel stereo system

If you want a question answered about a system, you must identify the gear by model numbers as well as brand names. What is the best way to wire subs for most power? Can someone please give me some guidance on next steps.

It all depends on what kind of car you have. And don't play a lot of distortion trying to get more bass - that'll damage the subs. That's a recipe for blowing subwoofers. The ideal voltage for a car audio system varies. If you want to learn more about installing amplifier systems, list of check out our Amplifier Installation Guide.

Getting More Bass When You Need It

Wood, The only safe way to wire that gear together is like this. For wiring subwoofers, we recommend using wires of to gauge in size. Im trying to get my system planned out before I hook up all the gear. Andy, Crutchfield carries a nice selection of Bluetooth car amplifiers that'll work for you.

Can you hook up two capacitors

It Still Works

Yahoo Answers

Pomerantz, just a follow up on my discovery. If so I am not sure of the wiring. Always use the biggest but most appropriate wire in case you decide to upgrade your sound system. Infinity doesn't publish what crossover points their drivers work with.

Would running in stereo make the amp run hotter? Then it goes from the amps to the speakers via speaker wires. Seth, The turn-on lead in the diagram is shown split like that for clarity. There will be some screws once you take them off lift up on the panel and pull it out.

Report Abuse

Right now the way i have it wired the amp will cut into protection mode if i have my volume turned too high. Share your experience with Bill Crutchfield. Did this article help you?

Pablo, You've picked out two subwoofers that will work great as a pair with that amp wired like this. After fiddling around the wires a while longer and some more retry's I noticed that the inline fuse on the power cable coming from the battery has blown. The way you can tell it is drawing too much power is if after the installation the car's headlights flicker or dim along with loud music. When do you want us to call you back?

Wiring Two Amps in One Car Audio System

Just figured I'd ask about certain things. Amplifier wiring diagrams How to add an amplifier to your car audio system. How do you wire a sub if your head unit does not have sub outputs? And why do I need to use a ground block? There is one additional subwoofer connection trick that you can take advantage of and it isn't that expensive.

  • How to install a car amplifier.
  • You'd connect the factory radio's speaker output wires to the amp's inputs via a harness or adapter.
  • Maybe its me an i was pushing them at what they could handle but im not sure whats your opinion?
  • Any more than that would require a relay to provide enough volt current to work.
  • Which amps would you recommend?
No Diagram Available
  1. Manuel, Your subs probably blew because they were being driven with twice their rated power.
  2. Juan, You are correct - the best practice is to ground all electrical components of a system at the same point.
  3. What would the wiring be if I wanted to wire both subs to one amp.
  4. How to bridge the amp is usually indicated at the amp's speaker wire terminals.
  5. Any idea what's going on here?

What would happen if you hooked it up and the subs blew? The second time I installed it and then want to a car audio shop to have them check it out to see if I had hook it up right and it was. If you do hook your amp up to the one-ohm setup, it will probably overheat or go into protect mode. Are power distrubution blocks absolutely necessary if I was installing two amps in the same system? Connect one power wire wire that connects from the battery to the amps to your distribution block.

Can I hook two amps up to one sub subwoofer speaker

Go to Corporate Sales page. Any suggestions or will my factory electrical system withstand that? As for what speakers and amp to get, why don't you or your daughter give us a toll-free call at and talk to an Advisor for help building the best system. How do you hook up two car stereo amplifiers one to each sub in there own box can you run a power wire out of one amp over to the other amp?

How do you wire a monoblock amp to two subs? Sameer, You should always use the inline fuse the manufacturer includes in their amp wiring kit. Zaheer, The number of speakers an amplifier can power at the same time completely depends on what kind of speakers they are, what their impedance is, and what their power ratings are. Felix, elite singles dating agency The in-line fuse on the power wire by the battery protects the wire and your car from fire in the event of a short circuit.

Buck Pomerantz

Both front and rear will need brackets in order to fit replacement speakers. Check out this article for tips on how. Eventually I moved back to Charlottesville, Virginia and opened a small demo recording studio. The amplifier has no effect on a sub's impedance. From the block outputs routed the wire to each amp.

  • Rival kingdoms matchmaking
  • Dating site canada single
  • Married dating ie
  • Dating early 20th century photos
  • Early dating scan kent
  • Dating sites singles
  • Lamborghini dating